You opened your GE dishwasher after a full cycle and found a puddle of gross, grimy water just sitting there at the bottom, yeah, that's not supposed to happen, and yeah, we can fix it.

Cartoon scene inside a kitchen. A frustrated homeowner stands in front of an ope

What's Actually Going On

When your GE dishwasher won't drain, the first instinct is to panic and price out a new machine. Don't. Nine times out of ten, dishwasher standing water comes down to one part: the drain pump. On most GE dishwashers, that's the WD26X10013 drain pump assembly, and it's one of the more replaceable components on the whole machine.

The drain pump's job is exactly what it sounds like, at the end of the wash cycle, it kicks on and forces all that dirty water out through the drain hose and into your kitchen drain line. When the pump motor burns out, the impeller cracks, or debris locks it up permanently, the water has nowhere to go. It just sits there getting stinkier by the hour.

Before you pull the pump, do a quick sanity check: make sure your drain hose isn't kinked, your garbage disposal knockout plug has been removed (classic rookie mistake if the disposal is new), and your filter basket isn't absolutely packed with food debris. If all that checks out and you've still got standing water after every single cycle, the GE dishwasher drain pump is your culprit. You might also hear the machine humming but not draining, that's the pump motor trying and failing. That's your smoking gun.

Cartoon close-up scene of the YAP Dude crouching in front of an open GE dishwash

The Fix

Here's how to swap in a new WD26X10013 and get your GE dishwasher draining like it should. You'll need a Torx T20 screwdriver, a flathead, some towels, and maybe a shallow pan to catch residual water.

  1. Kill the power. Unplug the dishwasher or flip the breaker. Non-negotiable.
  2. Pull the lower dish rack out and set it aside.
  3. Remove the filter assembly, twist it counterclockwise and lift it out. You'll likely find whatever finally murdered your old pump hiding in here.
  4. Access the pump housing. On most GE models, the pump sits beneath the spray arm hub at the bottom of the tub. Remove the spray arm (usually just a counterclockwise twist), then unscrew the pump cover.
  5. Disconnect the old pump. You'll unplug the wire harness connector and release the locking tabs holding the pump body in place. Have your towels ready, some water will come out.
  6. Drop in the new WD26X10013. Seat it firmly, reconnect the harness, and reinstall the pump cover. Everything clicks back the same way it came out.
  7. Reassemble, filter, spray arm, lower rack.
  8. Run a short cycle and watch that water disappear like it's supposed to.

The WD26X10013 typically runs in the $40, $70 range depending on where you source it. Come grab it at the Piedmont shop and you'll have it same-day instead of waiting a week for shipping.

Cartoon scene of the YAP Dude kneeling on a kitchen floor in front of an open GE

When to Call YAP vs. DIY

DIY this one. If you're comfortable with a screwdriver and following steps, this is a beginner-to-intermediate repair. No soldering, no special tools, no drama.

Call us if you've replaced the pump and the dishwasher still won't drain, at that point you might be looking at a control board issue or a wiring fault, and we'll help you figure out your next move.

Swing by the Piedmont shop or text 405-876-8100 and we'll pull a WD26X10013 off the shelf for you today, no waiting, no shipping fees, just get your kitchen back to normal.

Cartoon scene inside the YAP appliance parts store in Piedmont, Oklahoma. The YA
Need the part?

Part #WD26X10013, Drain Pump

Text us the part number and your model #, and we'll check stock + price for pickup at the counter in Piedmont. No call centers, no hold music.

Text to order →